Flat roofs & coatings
Spray foam roofing in Pembroke Pines, FL for low-slope roofs
Spray polyurethane foam forms one continuous, insulated layer across a flat roof, but it lasts only as long as the coating that shields it from the Florida sun.
- Open 24/7
- Based on Hiatus Road
- HVHZ-rated materials

- Real person on the line
- Visit booked on the same call
- Photos of what we find
Quick answer
Spray foam roofing applies spray polyurethane foam (SPF) over a low-slope roof, building one continuous insulated layer with no seams, then covers it with a coating that blocks UV. The foam can be sprayed thicker to improve drainage. The coating is renewed on a cycle, often every 10 to 15 years. Typical costs run $5.40 to $9.80 per square foot. Call (754) 226-1055, answered 24/7.
Spray foam roofing around Pembroke Pines
Spray foam suits the flat and low-slope roofs common on commercial buildings, warehouses, condo additions and some homes in Broward and Miami-Dade. The foam goes on as a liquid, expands within seconds and cures into a firm, closed cell layer that bonds to the roof below. It flows around curbs, drains and pipes, so there are far fewer joints for water to find.
The foam itself breaks down under sunlight, which is why the top coat matters as much as the foam. We spray only on a dry, prepared surface, check thickness as we go, and cover the foam with an acrylic or silicone coating at the rated thickness. Planned recoats keep the foam protected for decades, while a skipped recoat lets UV chalk and erode the surface.
When to call
Signs it is time for spray foam roofing
Worn flat roof, solid deck
An aging built-up or modified bitumen roof over a dry, solid deck can often be covered with foam instead of torn off.
Water sits for days
Low spots that hold water wear any roof faster, and foam can be sprayed thicker in those areas to build slope toward the drains.
Crowded with penetrations
Roofs packed with AC curbs, pipes and conduit are hard to flash with sheet membranes, while foam seals around each one in a single layer.
High cooling bills
A hot, poorly insulated flat roof drives up AC use, and the foam adds insulation across the whole roof at once.
Chalky or exposed foam
On an existing foam roof, a chalky surface or yellow-brown foam showing through means the coating is worn and a recoat is due.
Blisters or bird pecks
Raised bubbles, small holes from birds, or soft spots in an existing foam roof need cutting out and filling before water gets in.
How the job runs
What happens on your roof
- 01
Survey for moisture
We check the existing roof for wet insulation and soft deck, since foam must never be sprayed over trapped moisture.
- 02
Prepare the surface
Loose gravel, blisters and wet sections are removed, the surface is cleaned and primed, and edges and drains are prepared.
- 03
Spray the foam
Foam goes on in passes on a dry day with light wind, built thicker at low spots to send water toward the drains.
- 04
Apply the coating
The same day or the next, an acrylic or silicone coating goes on in two coats at the rated thickness, with granules added on walk paths.
- 05
Measure and document
We take thickness readings, photograph the roof, and give you a recoat schedule so the foam stays protected.

Local factors that change this job
Flat and low-slope roofs on Pembroke Pines shopping centers, office buildings and home additions face high UV, heavy afternoon storms and hurricane winds. In the HVHZ, a spray foam system, including its coating, must carry a Miami-Dade NOA or equivalent approval, and the work needs a permit and inspections. Spraying also depends on weather. Foam needs a dry surface and light wind, so summer jobs are planned around the afternoon rain that rolls in most days from June to September.
Your options
Choices worth understanding first
Acrylic coating
A water-based elastomeric coating that reflects heat well and costs less upfront. It needs good drainage, since long ponding wears it faster, and recoats come sooner.
Silicone coating
Silicone holds up better under ponding water and UV and keeps its reflectivity. It costs more, and new coats bond best to silicone, so future recoats stay with it.
Foam over the existing roof
When the old roof and deck are dry and sound, foam goes right over them, avoiding tear-off cost and keeping the building in use during the job.
Recoat of existing foam
If your foam roof is sound but the coating is worn, we clean it, repair damaged spots and apply a new top coat to restart the protection cycle.
Typical cost
What spray foam roofing costs in Pembroke Pines
| SPF, 1.5 inches with acrylic coating | $5.40 to $7.30 per sq ft |
| SPF, 1.5 inches with silicone coating | $6.20 to $9.80 per sq ft |
| Added foam to build slope, per inch | $0.85 to $1.70 per sq ft |
| Recoat of an existing foam roof | $2.15 to $3.90 per sq ft |
Price depends on roof size, foam thickness, how much slope has to be built in, the coating type, how many wet areas must be removed, and access for the spray rig. Small roofs cost more per square foot. The final price is set after an on-roof look and given to you in writing. Compare every service on the roofing price guide.
Questions
Spray foam roofing questions we hear
It depends on the coating type and thickness. Many acrylic coatings are renewed every 10 to 12 years, and silicone often lasts closer to 15. Look over the roof once a year and after major storms. When the coating looks thin or chalky or shows foam color through it, schedule a recoat before the foam itself starts to weather.
Not always. Foam can go over many existing built-up, modified bitumen and metal roofs if the deck and insulation are dry and the surface is sound. We check for moisture first. Wet areas are cut out and replaced, because foam sprayed over trapped water will blister and fail. Code limits on the number of roof layers also apply.
Foam bonds directly to the surface below, so there are no loose edges or laps for wind to lift. Approved SPF systems are tested for uplift, and in Broward and Miami-Dade the system must carry an HVHZ approval. The attachment of the deck underneath still matters, so we check it before spraying.
Yes, for normal service. Cured foam with its coating is firm enough for foot traffic, though sharp tools, dragged equipment and heavy point loads can dent or puncture it. We add granules or walk pads along the paths to AC units so service visits do not wear through the coating.
Related work
Often booked with this service
Silicone Roof Coating
Your flat or metal roof is worn but still dry underneath, and you want to add years of life without paying for a full tear-off.
See this serviceFlat Roof Repair
Water sitting on a flat roof for days after a storm finds every weak seam and drain gap, then shows up as a stain over the Florida room.
See this serviceCommercial Roofing
A leaking roof over a retail bay, office or warehouse costs you inventory, tenant goodwill and business days, so repairs need to happen fast and around the people inside.
See this serviceMore flat roofs & coatings services
Where we do this work most
Leak, storm damage or a roof that is simply getting old?
Call the roof line any hour. A real person answers, asks what you are seeing and sets the next step.