Skip to content
Aurora ShieldRoofing Contractors 24/7Call the roof line(754) 226-1055

Roof repair

Metal roof repair in Pembroke Pines, FL for panels and trim

Metal roofs handle South Florida wind well until a fastener backs out, a seam opens, or salt air starts to rust a cut edge, and then leaks follow quickly.

  • Open 24/7
  • Based on Hiatus Road
  • HVHZ-rated materials
Roofer replacing fasteners on a gray exposed fastener metal porch roof of a South Florida home with palm trees and blue sky
Answered 24/7
  • Real person on the line
  • Visit booked on the same call
  • Photos of what we find

Quick answer

Metal roof repair fixes standing seam and exposed fastener roofs: replacing worn screws and washers, resealing laps, refastening loose panels, replacing damaged panels and trim, and treating rust. Call when you hear panels rattle in wind or see rust or leaks. Typical repairs cost $475 to $2,280. Call (754) 226-1055, answered 24/7.

Metal roof repair around Pembroke Pines

Metal roofs are growing in Pembroke Pines, especially standing seam on newer custom homes and exposed fastener panels on sheds, porches and accessory buildings. Metal resists high winds when installed to HVHZ standards, but it moves with every hot afternoon and cool night. That expansion and contraction works screws loose and wears rubber washers until water slips in around them.

Repair starts with identifying the panel type and the original manufacturer's system, because standing seam clips, panels and trim are not interchangeable between brands. We replace fasteners with the correct size and washer, reseal laps with compatible sealants, and use matching metal and coatings so dissimilar metals do not corrode each other. Cut edges are treated to slow rust.

When to call

Signs it is time for metal roof repair

Rattling or loose panels

Panels that bang in the wind have lost fasteners or clips, and a loose panel can peel off entirely in a strong storm.

Backed out screws

Screw heads standing above the panel or with cracked washers let water in at every hole along the row.

Rust at edges or cuts

Orange rust along cut edges, laps or around fasteners shows the coating has failed, which happens faster near the coast.

Leaks at trim and ridges

Drips below ridge caps, eave trim or wall flashing often mean closure strips have failed or the sealant has dried out.

Dents and creases

Branch strikes or hail can dent panels and crack the paint finish, opening a path for corrosion over time.

Stains under vents

Penetrations through metal panels need special boots, so a stain under one usually means the boot or its sealant has failed.

How the job runs

What happens on your roof

  1. 01

    Identify the system

    We confirm whether the roof is standing seam or exposed fastener, the panel profile and gauge, and the coating, so replacement parts match.

  2. 02

    Check fasteners and seams

    Every row of screws, the laps, the ridge closures and the trim are inspected for loose fasteners, worn washers and open seams.

  3. 03

    Replace worn fasteners

    Failed screws are removed and replaced with correctly sized, coated fasteners and new washers, driven to proper tension without crushing the washer.

  4. 04

    Repair panels and trim

    Damaged panels, ridge caps or eave trim are replaced or refastened, and laps and closures are resealed with sealant compatible with the panel finish.

  5. 05

    Treat rust and document

    Surface rust is cleaned and primed, cut edges are touched up with matching paint, and you receive photos of every repaired area.

Close up of new lead pipe boot flashing being sealed on a tile roof
A typical day on a roof repair job in Broward County.

Local factors that change this job

In the HVHZ, metal roofing panels, clips and fasteners need Miami-Dade NOA or equivalent approval, and fastener spacing is tighter than in most of the country. Homes on the eastern side of Pembroke Pines, closer to the coast, see more salt in the air, which speeds corrosion on cut edges and uncoated fasteners. Afternoon heat followed by evening rain makes metal expand and contract daily, so regular fastener checks matter here. Replacing panels over a large area may need a permit.

Your options

Choices worth understanding first

Standing seam repair

Concealed clip systems need panels released and reseamed with the right tools. Repairs often involve opening a seam, replacing a panel, and reseaming without damaging neighboring panels.

Exposed fastener refresh

On screw down panels, replacing every fastener with a longer lasting screw and new washer can stop many leaks at once and extend the useful life of the roof.

Butyl and sealant choice

Lap sealants must be compatible with the panel finish. Butyl tape and polyether sealants hold up better under South Florida UV than cheap silicone caulk.

Galvalume versus painted panels

Galvalume resists corrosion well inland, while painted finishes add color and UV protection. Replacement panels should match the original metal to avoid galvanic corrosion.

Typical cost

What metal roof repair costs in Pembroke Pines

Typical South Florida range$475 to $2,280per repair visit
Fastener and washer replacement, per 100 screws$365 to $690
Single panel replacement$720 to $1,940
Ridge cap or trim reseal, per 10 feet$245 to $520
Rust treatment and touch up, per area$185 to $460

Price depends on panel type, how many fasteners or panels need replacing, roof pitch and height, the availability of matching panels and trim, and how much rust treatment is needed. Standing seam work usually costs more than exposed fastener repairs because panels must be released and reseamed. The final price is set after an on-roof look. Compare every service on the roofing price guide.

Questions

Metal roof repair questions we hear

Daily expansion and contraction from heat pushes and pulls on each screw. Over the years, that movement loosens screws, especially if they were overdriven or missed the purlin or deck below. Replacing them with the correct size and fresh washers, set to the right tension, usually solves the problem for many years.

Surface rust can be cleaned, primed and painted. If rust has eaten through the metal or spread under the paint over a large area, the panel should be replaced. Patching a rusted hole with sealant or a scrap of metal often traps moisture against the panel and makes the rust worse.

It can. Salt speeds corrosion at cut edges, scratches and fasteners. Homes closer to the ocean benefit from aluminum or coated steel panels rated for coastal exposure, stainless or coated fasteners, and an occasional fresh water rinse. Inland Pembroke Pines homes see less salt, but cut edges still need protection.

Replaced fasteners blend in well. New panels or trim may look brighter than faded originals at first. We source matching profiles and colors where possible, and on painted roofs the difference usually fades within a year or two of sun exposure. Galvalume panels dull to match more quickly.

Related work

Often booked with this service

Roof Repair

A small roof problem in South Florida rarely stays small, because every afternoon storm pushes more water past the cracked tile, lifted shingle or tired flashing you cannot see.

See this service

Roof Flashing Repair

Most roof leaks start where the roof meets a wall, a valley or a vent pipe, and the metal flashing there has rusted, cracked or pulled loose.

See this service

Roof Inspection

You are not sure what shape your roof is really in after another storm season, and a small stain or loose tile has you wondering what else is hiding.

See this service

More roof repair services

Where we do this work most

Leak, storm damage or a roof that is simply getting old?

Call the roof line any hour. A real person answers, asks what you are seeing and sets the next step.

Roof trouble? Answered 24/7Call (754) 226-1055